Connecting top and bottom SMD component pads using viaEagle is refusing to tie ground pads of SMD components...
Ban on all campaign finance?
Why must traveling waves have the same amplitude to form a standing wave?
Instead of Universal Basic Income, why not Universal Basic NEEDS?
Could the Saturn V actually have launched astronauts around Venus?
Counting certain elements in lists
How do anti-virus programs start at Windows boot?
How to explain that I do not want to visit a country due to personal safety concern?
Why are the outputs of printf and std::cout different
Science-fiction short story where space navy wanted hospital ships and settlers had guns mounted everywhere
How to deal with a cynical class?
Happy pi day, everyone!
My adviser wants to be the first author
Why did it take so long to abandon sail after steamships were demonstrated?
Informing my boss about remarks from a nasty colleague
Know when to turn notes upside-down(eighth notes, sixteen notes, etc.)
Have researchers managed to "reverse time"? If so, what does that mean for physics?
Professor being mistaken for a grad student
An Accountant Seeks the Help of a Mathematician
What is the greatest age difference between a married couple in Tanach?
Welcoming 2019 Pi day: How to draw the letter π?
2D counterpart of std::array in C++17
Why is "das Weib" grammatically neuter?
Where is the 1/8 CR apprentice in Volo's Guide to Monsters?
Is having access to past exams cheating and, if yes, could it be proven just by a good grade?
Connecting top and bottom SMD component pads using via
Eagle is refusing to tie ground pads of SMD components to the ground planeDipTrace bottom layer pad shapeEagle configure autorouter to solder components (except vias) only on bottom layer of double sided PCBIs every pad in eagle a via?Eagle: polygon pour leaving funny blank areasRouting and placement of decoupling capacitor when using power planeA confusion on using PCB copper pourPlacing the pads of SMD components in different layers (KiCad PCB design)How to prevent tombstoning using via-in-pad with small SMD discretesPastemask for through hole components
$begingroup$
I am working on a 2 layer board and the PCB will be a double sided job. Some components on the top layer will have exact mirrors on the bottom right under them. My question is, for SMD components, can I just connect those pads with a via right in the center of the pads?
Does this affect electrical performance or production/assembly in any shape or form?
The reason: The bottom layer is a copper pour for ground and I have pads that belong to GND net so why not?
Please see the picture below (for demonstration porpuses I have moved the top component a little bit higher).
P.S. The components are TVS diodes (SM8J36CA). But my qustion is more general and is about wherever the pad size allows hosting a via in its center!
pcb pcb-design analog pcb-fabrication pcb-assembly
edited 3 hours ago
JRE
22.2k43771
asked 4 hours ago
Sean87Sean87
1,543123360
$endgroup$
add a comment |
$begingroup$
I am working on a 2 layer board and the PCB will be a double sided job. Some components on the top layer will have exact mirrors on the bottom right under them. My question is, for SMD components, can I just connect those pads with a via right in the center of the pads?
Does this affect electrical performance or production/assembly in any shape or form?
The reason: The bottom layer is a copper pour for ground and I have pads that belong to GND net so why not?
Please see the picture below (for demonstration porpuses I have moved the top component a little bit higher).
P.S. The components are TVS diodes (SM8J36CA). But my qustion is more general and is about wherever the pad size allows hosting a via in its center!
pcb pcb-design analog pcb-fabrication pcb-assembly
edited 3 hours ago
JRE
22.2k43771
asked 4 hours ago
Sean87Sean87
1,543123360
$endgroup$
2
$begingroup$
Talk to whoever is doing your assembly. Vias-in-pads generally wick solder away from the joint, causing reliability issues.
$endgroup$
– Dave Tweed♦
4 hours ago
2
$begingroup$
I wouldn't try it due to issues that can arise. They do this on BGAs where space is at a premium and it's called "via-in-pad" but they take special measures to make sure it works.
$endgroup$
– Toor
4 hours ago
2
$begingroup$
It's possible, but not recommended. If you're hand-assembling them, it should be okay, if a little harder to keep together. If this is for automated assembly, don't do it unless you really have no other option.
$endgroup$
– Hearth
4 hours ago
add a comment |
$begingroup$
I am working on a 2 layer board and the PCB will be a double sided job. Some components on the top layer will have exact mirrors on the bottom right under them. My question is, for SMD components, can I just connect those pads with a via right in the center of the pads?
Does this affect electrical performance or production/assembly in any shape or form?
The reason: The bottom layer is a copper pour for ground and I have pads that belong to GND net so why not?
Please see the picture below (for demonstration porpuses I have moved the top component a little bit higher).
P.S. The components are TVS diodes (SM8J36CA). But my qustion is more general and is about wherever the pad size allows hosting a via in its center!
pcb pcb-design analog pcb-fabrication pcb-assembly
edited 3 hours ago
JRE
22.2k43771
asked 4 hours ago
Sean87Sean87
1,543123360
$endgroup$
I am working on a 2 layer board and the PCB will be a double sided job. Some components on the top layer will have exact mirrors on the bottom right under them. My question is, for SMD components, can I just connect those pads with a via right in the center of the pads?
Does this affect electrical performance or production/assembly in any shape or form?
The reason: The bottom layer is a copper pour for ground and I have pads that belong to GND net so why not?
Please see the picture below (for demonstration porpuses I have moved the top component a little bit higher).
P.S. The components are TVS diodes (SM8J36CA). But my qustion is more general and is about wherever the pad size allows hosting a via in its center!
pcb pcb-design analog pcb-fabrication pcb-assembly
pcb pcb-design analog pcb-fabrication pcb-assembly
edited 3 hours ago
JRE
22.2k43771
asked 4 hours ago
Sean87Sean87
1,543123360
edited 3 hours ago
JRE
22.2k43771
asked 4 hours ago
Sean87Sean87
1,543123360
edited 3 hours ago
JRE
22.2k43771
edited 3 hours ago
JRE
22.2k43771
edited 3 hours ago
JRE
22.2k43771
22.2k43771
asked 4 hours ago
Sean87Sean87
1,543123360
asked 4 hours ago
Sean87Sean87
1,543123360
asked 4 hours ago
Sean87Sean87
1,543123360
1,543123360
2
$begingroup$
Talk to whoever is doing your assembly. Vias-in-pads generally wick solder away from the joint, causing reliability issues.
$endgroup$
– Dave Tweed♦
4 hours ago
2
$begingroup$
I wouldn't try it due to issues that can arise. They do this on BGAs where space is at a premium and it's called "via-in-pad" but they take special measures to make sure it works.
$endgroup$
– Toor
4 hours ago
2
$begingroup$
It's possible, but not recommended. If you're hand-assembling them, it should be okay, if a little harder to keep together. If this is for automated assembly, don't do it unless you really have no other option.
$endgroup$
– Hearth
4 hours ago
add a comment |
2
$begingroup$
Talk to whoever is doing your assembly. Vias-in-pads generally wick solder away from the joint, causing reliability issues.
$endgroup$
– Dave Tweed♦
4 hours ago
2
$begingroup$
I wouldn't try it due to issues that can arise. They do this on BGAs where space is at a premium and it's called "via-in-pad" but they take special measures to make sure it works.
$endgroup$
– Toor
4 hours ago
2
$begingroup$
It's possible, but not recommended. If you're hand-assembling them, it should be okay, if a little harder to keep together. If this is for automated assembly, don't do it unless you really have no other option.
$endgroup$
– Hearth
4 hours ago
2
2
$begingroup$
Talk to whoever is doing your assembly. Vias-in-pads generally wick solder away from the joint, causing reliability issues.
$endgroup$
– Dave Tweed♦
4 hours ago
$begingroup$
Talk to whoever is doing your assembly. Vias-in-pads generally wick solder away from the joint, causing reliability issues.
$endgroup$
– Dave Tweed♦
4 hours ago
2
2
$begingroup$
I wouldn't try it due to issues that can arise. They do this on BGAs where space is at a premium and it's called "via-in-pad" but they take special measures to make sure it works.
$endgroup$
– Toor
4 hours ago
$begingroup$
I wouldn't try it due to issues that can arise. They do this on BGAs where space is at a premium and it's called "via-in-pad" but they take special measures to make sure it works.
$endgroup$
– Toor
4 hours ago
2
2
$begingroup$
It's possible, but not recommended. If you're hand-assembling them, it should be okay, if a little harder to keep together. If this is for automated assembly, don't do it unless you really have no other option.
$endgroup$
– Hearth
4 hours ago
$begingroup$
It's possible, but not recommended. If you're hand-assembling them, it should be okay, if a little harder to keep together. If this is for automated assembly, don't do it unless you really have no other option.
$endgroup$
– Hearth
4 hours ago
add a comment |
1 Answer
1
active
oldest
votes
$begingroup$
I am working on a 2 layer board and the PCB will be a double sided
job. Some components on the top layer will have exact mirrors on the
bottom right under them. My question is, for SMD components, can I
just connect those pads with a VIA right in the center of the pads?
Yes, will the assembly house be happy about it? No. Vias wick solder through them, plus using a stencil will apply the wrong amount of solder for the component because most of it will be in the hole.
If you do this, let the assembly house know (or if your hand soldering them who cares?) They will probably need to hand solder this component.
Does this affect electrical performance or production/assembly in any
shape or form?
If the signals in question aren't running at the +50Mhz speed then no, a few nH of inductance isn't going to make a difference. Vias might slow down very fast ESD events, if this is the only inductor in the current path which is unlikely. if adding a 10's of nH to the design makes a difference then run a PCB via inductance calculator and parallel the vias or do something else.
answered 3 hours ago
laptop2dlaptop2d
26.3k123381
$endgroup$
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f427294%2fconnecting-top-and-bottom-smd-component-pads-using-via%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
I am working on a 2 layer board and the PCB will be a double sided
job. Some components on the top layer will have exact mirrors on the
bottom right under them. My question is, for SMD components, can I
just connect those pads with a VIA right in the center of the pads?
Yes, will the assembly house be happy about it? No. Vias wick solder through them, plus using a stencil will apply the wrong amount of solder for the component because most of it will be in the hole.
If you do this, let the assembly house know (or if your hand soldering them who cares?) They will probably need to hand solder this component.
Does this affect electrical performance or production/assembly in any
shape or form?
If the signals in question aren't running at the +50Mhz speed then no, a few nH of inductance isn't going to make a difference. Vias might slow down very fast ESD events, if this is the only inductor in the current path which is unlikely. if adding a 10's of nH to the design makes a difference then run a PCB via inductance calculator and parallel the vias or do something else.
answered 3 hours ago
laptop2dlaptop2d
26.3k123381
$endgroup$
add a comment |
$begingroup$
I am working on a 2 layer board and the PCB will be a double sided
job. Some components on the top layer will have exact mirrors on the
bottom right under them. My question is, for SMD components, can I
just connect those pads with a VIA right in the center of the pads?
Yes, will the assembly house be happy about it? No. Vias wick solder through them, plus using a stencil will apply the wrong amount of solder for the component because most of it will be in the hole.
If you do this, let the assembly house know (or if your hand soldering them who cares?) They will probably need to hand solder this component.
Does this affect electrical performance or production/assembly in any
shape or form?
If the signals in question aren't running at the +50Mhz speed then no, a few nH of inductance isn't going to make a difference. Vias might slow down very fast ESD events, if this is the only inductor in the current path which is unlikely. if adding a 10's of nH to the design makes a difference then run a PCB via inductance calculator and parallel the vias or do something else.
answered 3 hours ago
laptop2dlaptop2d
26.3k123381
$endgroup$
add a comment |
$begingroup$
I am working on a 2 layer board and the PCB will be a double sided
job. Some components on the top layer will have exact mirrors on the
bottom right under them. My question is, for SMD components, can I
just connect those pads with a VIA right in the center of the pads?
Yes, will the assembly house be happy about it? No. Vias wick solder through them, plus using a stencil will apply the wrong amount of solder for the component because most of it will be in the hole.
If you do this, let the assembly house know (or if your hand soldering them who cares?) They will probably need to hand solder this component.
Does this affect electrical performance or production/assembly in any
shape or form?
If the signals in question aren't running at the +50Mhz speed then no, a few nH of inductance isn't going to make a difference. Vias might slow down very fast ESD events, if this is the only inductor in the current path which is unlikely. if adding a 10's of nH to the design makes a difference then run a PCB via inductance calculator and parallel the vias or do something else.
answered 3 hours ago
laptop2dlaptop2d
26.3k123381
$endgroup$
I am working on a 2 layer board and the PCB will be a double sided
job. Some components on the top layer will have exact mirrors on the
bottom right under them. My question is, for SMD components, can I
just connect those pads with a VIA right in the center of the pads?
Yes, will the assembly house be happy about it? No. Vias wick solder through them, plus using a stencil will apply the wrong amount of solder for the component because most of it will be in the hole.
If you do this, let the assembly house know (or if your hand soldering them who cares?) They will probably need to hand solder this component.
Does this affect electrical performance or production/assembly in any
shape or form?
If the signals in question aren't running at the +50Mhz speed then no, a few nH of inductance isn't going to make a difference. Vias might slow down very fast ESD events, if this is the only inductor in the current path which is unlikely. if adding a 10's of nH to the design makes a difference then run a PCB via inductance calculator and parallel the vias or do something else.
answered 3 hours ago
laptop2dlaptop2d
26.3k123381
answered 3 hours ago
laptop2dlaptop2d
26.3k123381
answered 3 hours ago
laptop2dlaptop2d
26.3k123381
answered 3 hours ago
laptop2dlaptop2d
26.3k123381
26.3k123381
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f427294%2fconnecting-top-and-bottom-smd-component-pads-using-via%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
2
$begingroup$
Talk to whoever is doing your assembly. Vias-in-pads generally wick solder away from the joint, causing reliability issues.
$endgroup$
– Dave Tweed♦
4 hours ago
2
$begingroup$
I wouldn't try it due to issues that can arise. They do this on BGAs where space is at a premium and it's called "via-in-pad" but they take special measures to make sure it works.
$endgroup$
– Toor
4 hours ago
2
$begingroup$
It's possible, but not recommended. If you're hand-assembling them, it should be okay, if a little harder to keep together. If this is for automated assembly, don't do it unless you really have no other option.
$endgroup$
– Hearth
4 hours ago